Видео

no torque wrench, no specs, just brrt that thing right on

Thank you so much! I had this exact same problem! I saw a piece I never saw before on the floor of my front seat and this video helped me fix the issue on my own!

Thank you for this video. Just what I needed to save a million dollars

Man thanks so much. Makes going into someone else's vehicle easier. Trying to help a friend and now I'm going to show up like a pro lol

Tanks Mista Roy😘

Thanks Roy you're awesome.

I wonder if he changes his oil by pumping the oil up through the drain hole.

Will the truck start if the shift linkage comes off?

Will the truck start if the gear linkage pops off

I love these "how not to do things right" videos. Thank you, sir!

Good!

THANK YOU

Great 😅

Any reason to use both ratchets vs just the one? are two needed?

Mahalo for making this video! Very helpful!

Good job!

Sometimes you need heat and oil

Roy THANK YOU SO MUCH! You have no idea how much I appreciate you. This video save me $600 or more. I thought it was the starter. My car would not turn on. And the gear stick was gliding up and down. The little rubber was all broken up. 20 minutes doing the repair and it is working like a charlar! Thanks again. Blessings

Worked great. Thank you so much

i just buy 2015 and the strauts is fine ...has 200.000

1. @10:32, the motor was jacked up, why, for easy access to the pulley? 2. How to adjust the belt tension? 3. Does it recommend to repalce the idle pulley too?

2008 Nissan Titan 👌🏿

What exact company and part is it? Can you order one online?

Thank you!

The Nr. 1 resin you change it is cause it absorbs water and water will boil when brakes heat up,if it boils you get bubbles=air,which will compress,so you get a very soft breaking pedal

Dude,it's supposed to be the other direction 😂 fill up at the master and drain at the calliper

Great!

I agree with the others below- Roy has created a very, very helpful video especially if you are daunted as I was to do brake caliper replacement on an old Tacoma. Really isnt bad at all with this video, and now my brakes feel nice and brakey. Thanks Roy!

Finally a video that actually details and shows where the anti rattle clips go.

Thanks for the video! I was able to knock this out in under 3 hours minus the recharge. Also left the tire on, tight squeeze but it worked. Sloped driveway 😅

Is this a joke???!!!!!

I appreciate the video

nice looking tools but sloppy workmanship and not a thorough basic explanation. a car had 4 wheels in which he didnt mention anything about the other 3 wheels nor did he mentionthe vasic operationof the master cylinder in relation to the calipers. he didnt even state that hey, this is your master cylinder.

Why even attempt to go against gravity. Of course the best way is to pressurize but at the very least, common sense should tell you to work with gravity and not against it. My favorite tho was filling with fluid and then emphasizing to be sure and put the screen back in. 😂 I'm not trying to be a hater either but dude, why you wanna get on RUclips - worldwide audience - and talk about something you obviously have no idea how to do. Thank God for the comments section on some of these vids.

I would never have figured out how to compress the brake caliper without this video! It's not 1974 any more -- electronics are everywhere.

Did u use the flush before draining the old oil?

Thanks man Gby

Don’t touch that shit with your bear hands dude. Have you ever seen what it does to plastic?🤦🏽‍♂️

🤣🤣

First off thanks for the video! Very straightforward and diy friendly! I only need to change Pads, do I still need to bleed the brakes?

thank you very much! fixed by 2005 accord - removing the front panel was the biggest challenge! .... but finally it worked. so happy - though orielly charged me $10 for the part which was a bit excees amazon had it for $4 but couldn't wait ...

Who is this wise dude

Why do you need that connector grease?

Too easy ,, Thankyou Ser,,

Wow! Thanks a lot! God bless you Mr Roy!

Wouldn’t want to buy any car he ever owned

Wow. So glad I found this video. You are the man! Thanks for the time it took to make the video. It really helped.

Why don’t you guys just read your owners manual….

Yours wasn't stuck, dude. That doesn't work when it's stuck.

If U follow this clowns advise you will be pushing old contaminated fluid back in through the anti lock module.And that is the exact wrong way to flush old fluid out of your system Do not listen to this guy